Williams "tales Of The Arabian Nights" Operations Manual : Williams Electronics Video Games, Inc : Free Download, Borrow, And Streaming : Internet Archive
When I plugged the original display back in, I got nothing once more. Older, dying displays draw extra energy, so that's the reason a newer display labored on the decrease voltages while the unique, drained display did not. The very first thing you will notice when disassembling Tales of the Arabian Nights is that all the ramps are connected to one another. There is only a single ramp entrance on the playfield, and a diverter sends the ball to the left or the proper ramps. The plastic is thin, and for the rationale that ramp pieces are quite giant, breaking them is a possibility. If you do break a ramp, or you just want to substitute it, you can rest assured because they are often replaced both individually or as a set .
For some cause, Tales of the Arabian Nights has no recess within the playfield for the ramp to sit in, so the ramp sits on prime of the playfield surface. The top edge of the ramp sits a number of millimetres above the playfield, which the ramp flap covers. There is a noticeably steeper incline over this ramp flap in comparison with different WPC video games the place the ramps sit in the recess.
Lamp boards are always problematic because of the lamp sockets themselves, the socket solder pads, or the header pins, as described on Pinwiki. The header pins have been the problem on this case, with one pin having cracked solder at its base. Another problem I seen after tales of the arabian nights pinball remake I first noticed the machine was that not one of the backbox general illumination lamps have been working. The backbox mild panel is linked to the facility driver board via an in-line connector, so I suspected this had just been left unplugged.
Most of the components are the same as those used on the dot matrix controller board in WPC-89 games. See my earlier weblog entry for a list of relevant parts. The primary difference is you received't need as many 1N4004 diodes, but you will need two extra 150K ohm resistors .
Princess, Here I Come!
And the one final step was to switch the light panel lamps with LEDs as a substitute of incandescents. tales of the arabian nights pinball machine for sale, will brighten the backbox up properly, generate far less heat, and devour much less energy. Once this was all carried out, I was capable of flip the sport on, saw each single GI lamp working, and breathed an enormous sigh of reduction. It was a lot of work to fix all of the previous hacks, but the lamps are now bulletproofed for the longer term.
Williams "tales Of The Arabian Nights" Operations Handbook
However, every little thing that had failed has now been replaced, so this show and audio/visual board must be good for some time. Plastics in poor condition; some broken and some replaced with clear items of plastic. Legs in poor condition; bolts have been covered in glue and one leg bracket was stripped. We have a quantity of shipping methods to accommodate your needs.
This one raised and lowered as expected, however when activating the plunger manually I discovered that there was a lot of resistance when the cage was pushed upwards. The left cage is situated in close proximity to the rubber ring above and to the left of the outlane. It's so shut that the rubber ring really rubs towards the publish spikes after they elevate and decrease. Now, it would not put enough strain on them to forestall motion, nevertheless it might exacerbate any other issues the meeting could be having. Potentially, thinner rubber rings would alleviate this problem, however I don't have any which are thinner than regular. For now, this doesn't look like an enormous concern, however undoubtedly one to keep a watch on.
Number Of Multiball Modes
The pinouts are completely different, resulting in a ribbon cable for one not essentially working for another! After some trial and error, I finally obtained the entire coin outputs assigned to the proper pins on the coin door interface board. Coin mechs are merely units which type coins of various sizes, determine they're legitimate currency, then trigger a switch based mostly on the currency worth of the coin. When playing with these mechs, a very handy useful resource is the Coin Door NRI Conversion for WPC doc which contains instructions of tips on how to program, install, and set up NRI coin mechs. Coin mechs communicate with the CPU board by way of a coin door interface board mounted to the left facet of the cupboard interior, close to the lean bob.
The backbox flasher is wired to the eject flashers, and fires in sync with them. The flashers really worked, but the problem was that they worked even once they shouldn't. Whenever a flipper or different playfield coil fired, all three flashers would activate briefly. It wasn't overly noticeable, however you'll see it should you were watching the sport. Once all of that was sorted, there was one last problem to unravel. I verified the voltages being produced by the board have been correct, and that there have been no connector points.